关于动态改变STM32 PWM占空比的问题
}
在主程序里改变对比值来改变PWM 占空比，上面的程序是不是太笨了，有没有其他方法，请高手指点
MCU2008 (2008-9-12 10:43:53)
是太笨了...
sunke9 (2008-9-12 10:47:56)
我的用法和你一样
while (1)
{
Delay(0x0000FFFF);
CCR1_Val = ADC_ConvertedValue*4;
CCR2_Val = 16000 - ADC_ConvertedValue*4;
TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM1;
TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable;
TIM_OCInitStructure.TIM_Pulse = CCR1_Val;
TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High;
TIM_OC1Init(TIM2, &TIM_OCInitStructure);
TIM_OC1PreloadConfig(TIM2, TIM_OCPreload_Enable);
}
while (1)
nomoneyiv (2008-9-12 11:29:08)
在中断里搞！
nomoneyiv (2008-9-12 11:33:22)
比如：
void TIM1_UP_IRQHandler(void)
{
TIM1_SetCompare1(pwm_val_c1);
TIM1_SetCompare3(pwm_val_c3);
TIM1_SetCompare2(pwm_val_c2);
TIM1_ClearITPendingBit(TIM1_IT_Update);
}
然后在主循环里，更改值
void TIM1_UP_IRQHandler(void)
{
}
然后在主循环里，更改值
pwm_val_c1++;
之类的。
020411 (2008-9-12 15:21:42)
谢谢
STM32青菜
yemingxp (2008-9-12 20:02:26)
aleyn (2008-9-15 14:05:15)
此贴最终解惑者是谁？
sw笨笨 (2009-2-24 07:31:01)
while (1)
//无限循环
{
CCR4_Val=CCR4_Val+0x1000;
//变量递增
if(CCR4_Val >= 0xffff) CCR4_Val=0;
//变量归零
TIM_SetCompare4(TIM3, CCR4_Val);
//变更长度
Delay(0xffff);
//延时
{
}
selina (2009-12-12 15:28:56)
好像只能在中断内做吧
wslaurora (2010-1-26 15:48:33)
通过tim更新时间触发DMA传输（循环模式），岂不是更简单？
TIM_DMACmd(TIM1, TIM_DMA_Update, ENABLE);
DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)TIM1_CCR1_Address;
//TIM1通道1外设捕获/比较寄存器首地址
DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)SRC_Buffer;
//内存数据缓存首地址
DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;
//外设作为数据传输的目的
DMA_InitStructure.DMA_BufferSize = 256;
//DMA缓存大小为256
评论